一、開料
First, open material
開料同柜身板一樣，就是門板的質地材料更多樣化，對板材進行切割，高端用開料據或激光切割機，低端用手工推臺鋸，一體加工中心設備有的也帶開料據。
Is expected to open with the cabinet body, door material is more diverse, on the plate cutting, cutting with high-end or low-end according to the laser cutting machine, hand push table saw, integrated processing center equipment with some materials according to.
二、開槽
Two, slotting
開槽的主要目的是安裝拉手，開槽不能將門板的寬度開完，要留一點封口，否則拉手要從另一面抽出來了。開槽的厚度要和拉手的型號一致，要略小于拉手的插入厚度。雕刻機、推臺鋸、開料鋸都可以進行開槽。
The main purpose of slotting is to install the handle, the slot can not open the width of the door plate, want to leave a little seal, otherwise the handle should be pulled out from the other side. Slotted thickness and handle the same model, slightly less than the thickness of the insertion handle. Engraving machine, push table saw, open saw can be slotted.
三、封邊
Three, edge banding
不同的材質決定是否需要封邊，常見的封邊材質有三聚氰胺、防火板、水晶板等。封邊一般為門板的同色，一般為2mm的厚度，產品可以使用鋁封邊。機器用自動封邊機、輕型封邊機等都可以。

Different materials determine whether it needs edge banding. The common edge materials are melamine, fireproof board, crystal board and so on. The edge is generally the same color as the door panels, generally 2mm thickness, high-end products can use aluminum edge. Automatic edge banding machine, light edge banding machine and so on.

四、打孔
Four, punching
此處的打孔為門鉸孔，移門軟包產品可以是2-3個鉸鏈，移門軟包可以3-4個鉸鏈，上下邊距鉸中心120為優。
Here is the door hinge hole drilling, the product can be a 2-3 soft door hinge, door hinge on a soft 3-4, below from the hinge center 120 is excellent.
五、鑼槽（雕刻）
Five, Gong groove (carving)
鑼槽就是在門板上進行雕刻花紋，可以說是凸顯檔次和產品銷量的關鍵步驟，設備對步驟的影響比較大，普通木工雕刻機可以進行簡單的線條雕刻，但是復雜的圖形需要用到2把以上的刻刀，那么普通木工雕刻機就無能為力，這時可以選擇多工序木工雕刻機或者一步到位直接選擇上木工加工中心。多工序雕刻機可以自動換刀比人工換刀雕刻的精度要高，速度也更快，適合5把刀以下的雕刻圖形，如果需要5把以上的圖形雕刻那么是選擇木工加工中心，標配刀庫是8把，省心省力，適合任何高級圖形的雕刻。
Gong groove is carved on the door, can be said to be a key step to highlight the quality and product sales, equipment on the steps of the impact is relatively large, the general woodworking engraving machine can be a simple line carving, but complex graphics need to use more than 2 of the knife, the general woodworking engraving machine is incapable of action, then you can selection of multi process woodworking engraving machine or one step direct selection of wood processing center. Multi process engraving machine can automatically change the knife to be higher than for artificial carving knife precision, speed is also faster, for the following 5 knife engraving graphics, if you need more than 5 graphics so it is best to choose the carved wood processing center, the standard knife is 8, worry and effort, for any advanced graphics carving.
六、吸塑
Six, blister
首先對門板進行打磨，然后噴膠，再將門板放入吸塑機即可，所用機器決定工藝品質，設備是真空吸塑機。
The door for grinding, and then glue, then the door into the plastic machine, the machine process quality, equipment is vacuum machine.
七、烤漆
Seven, baking paint
主要有人工完成，工藝比較復雜，建議找熟練的有經驗技術的工人完成，主要步驟是：打磨——給鉸邊、封邊處上密封底漆——進行雙面人工打磨——晾干——再打磨——噴面漆——烤房烘烤——?dú)鈩糯蚰ィǔ龎m、憑證）——水磨——拋光——單面去紙等步驟。主要設備有磨槍、磨機等手工設備。
The main manual work, the process is complex, suggests looking for experienced skilled technology workers to complete, the main steps are: - to the hinge side edge grinding on sealing primer - Double - dry - grinding manual polishing, spray paint, curing barn - Jin (dust, gas proof) - grinding mill - - one side paper polishing steps. The main equipments are guns, mill and other equipment manual.
本文來自：移門生產設備更多的精彩內容請點擊我們的官方網站：http://www.hnyfqpj.cn我們會有專門的客服為您解答。
This article from the production equipment: the more exciting content please click on our official website: http://www.hnyfqpj.cn we will have a special service for you to answer.