1、 每日需檢查鋁型材切割機油杯有無潤滑油，我公司使用20#的空壓潤滑油，應保持七分滿，避免空壓零件無潤滑油而減少使用壽命，檢查壓力是否保持6-7kg的壓力才能操作，壓力太大或太小易使空壓零件受損，本機的濾水器有自動排號水功能，如不能自動排水請自行更換濾水器裝置，避免管路積水，影響機臺工作
1, daily check aluminum cutting oil cup has no lubricating oil, I use the 20# air compressor lubricating oil, should maintain a full seven to avoid air compressor parts without lubricating oil and reduce the service life, check whether the pressure to keep the pressure of 6-7kg to operation, the pressure is too large or too small to make air compressor parts damaged water filter, this machine has the automatic arranging water function, if not please replace the automatic drainage device of water filter, avoid water pipeline, affect the machine work
2、 電源在不使用時需將熔斷絲開關保持關閉狀態，以確保機器及人員的安全
2, the power supply does not use, the fuse switch to stay closed, to ensure the safety of the machine and personnel
3、 在加油潤滑處，支桿和壓料架環配合處、連桿架前后軸、氣缸接頭及入出料中滾輪兩頭配合處，需每周檢查一次，適時加油潤滑，可避免卡死而造成停機之損失
In 3, lubrication, rod and pressure ring, connecting rod rack frame, front and rear axle cylinder joint and fit into and out of two roller material, should be checked once a week, timely lubrication, can avoid the loss caused by the shutdown of the death card
4、 切削油：本噴油組可噴CPC-R32或皂化油，風量可調整且左右油量可分開控制使用鋁合金切削油或水溶性切削油（皂化油）1：20，比例不能太稀，避免水分太重造成生銹或卡死，需每日檢查油量是否足夠，不足時需補充，充分冷卻可增加刀具的壽命，減少鋁切的毛邊。
4, cutting oil: the injection group CPC-R32 injection or oil saponification, air volume can be adjusted and the right amount of oil can be separated from the control soluble cutting oil Aluminum Alloy cutting oil or water (oil saponification) 1:20 ratio can not be too thin, too heavy to avoid moisture caused by rust or stuck, daily check the amount of oil is not enough, enough to supplement sufficient cooling can increase the tool life, reduce the burr of aluminum cutting.

5、 保持工作臺面的清潔可確保鋸切的精度
5. Keep the work table clean, ensure the precision of sawing
6、 每日檢查風管有無破損，如有破損請更換新的風管，避免因漏水導致機器無法正常工作
6. Check the pipe for damage every day. If damaged, please replace the new air pipe to avoid the leakage, the machine can not work properly
7、 油桶使用CPC-R68的液壓油，需保持七分滿，可確保氣缸動作順暢，加油時先將氣源關OFF后蓋取下，打開油桶上方的油蓋，將油加至七分滿后，關上油蓋，倘上后蓋即可。
7, the use of CPC-R68 hydraulic oil drums, need to keep seven full, can ensure that the cylinder moves smoothly, gas when the first source OFF cover removed, the drum is opened at the top of the oil cap, oil will be increased to seven points after the close oil cover, if the back cover can be.
8、 定期（每周一次）需檢查皮帶是否過度磨損，是否平行、皮帶表面壓力是否過松或過緊。
8, regular (preferably weekly) to check whether the excessive wear of the belt, whether parallel, the belt surface pressure is too loose or too tight.
9、 操作時氣壓零件如有故障或不動作的情形，請更換故障的空壓零件
9. If the air pressure parts are faulty or not in operation, replace the spare parts
10、噴油冷卻系統使用噴油器，利用虹吸原理將冷卻油吸至噴嘴，冷卻鋸片，為避免空壓零件雜物阻塞而產生故障。
10 、 the injection cooling system uses an injector, which uses the siphon principle to suck the cooling oil into the nozzle and the cooling saw blade to avoid the blockage of the parts in the air pressure parts.
更多的關于鋁切割設備的問題或者詳細的內容，請進入我們公司的網站：http://www.hnyfqpj.cn/    網站中會有很多的內容僅供參考。
About the problem of aluminum cutting equipment or more details, please enter our website: http://www.hnyfqpj.cn/ There will be a lot of content on the site for your reference only.