1、設備出現異常應立即停車檢修，故障排除后再行運轉。
1, abnormal equipment should immediately stop maintenance, troubleshooting after the operation.
2、各處軸承和鏈輪處應定期加住潤滑脂和潤滑油，減速機6個月加注一次，
2, each place bearing and sprocket should regularly add grease and lubricating oil, reducer once every 6 months,
板壓段的導軌及兩導軸應經常加注潤滑油。
Lubricating oil should be often added to the guide rail and the two guide shaft of the pressure plate.
3、每工作5000小時后，應對角接觸球軸承進行清洗，添加NBU-15潤滑脂或鋰基潤滑脂（SY1412-75），添加量為內腔面積的1∕3～2∕3左右，軸承達不到精度時可更換。切記：清洗干燥部分的清洗室不能任何潤滑油和非中性液體，避免水源被污染。

3, every 5000 hours of work, should the angular contact ball bearing cleaning, NBU-15 grease or lithium grease additive (SY1412-75), was added to the 1 lumen area / 3 ~ 2 / 3 or so, can not reach the accuracy of bearing replacement. Remember: cleaning the drying part of the cleaning room can not be any lubricating oil and non neutral liquid, to avoid water pollution.

4、經常檢查電氣線路，有否破損或鼠咬，各接頭處有否松動，電控箱內應保持整潔、干燥。
4, often check the electrical circuit, whether damaged or rodent bite, the joints are loose, the electrical control box should be kept clean and dry.
5、每段氣缸及其它活動處要經常注入潤滑油，電磁閥板應保持清潔，接頭可靠
5, each segment of the cylinder and other activities should be regularly injected lubricating oil, solenoid valve plate should be kept clean, reliable joints
6、設備上的灰塵應及時擦凈，設備背靠板、背靠輪要保持清潔，每個工作班次要及時清除灰塵和雜質。
6, dust on the equipment should be promptly wiped, equipment back plate, back wheel to keep clean, each work shift should promptly remove dust and impurities.
7、三聯體（分水濾氣器每班防水，每周清洗一次，壓力表調至0.5～0.8mpa,油霧器保持一定油位，機械油（N32#）滴油時調整到每分鐘一滴左右。
7, three conjoined (water separator gas filter each class waterproof, cleaning once a week, the pressure gauge is adjusted to 0.5 ~ 0.8MPa, oil mist to maintain a certain oil level, mechanical oil (N32#) drops when the oil is adjusted to about one drop per minute.
8、經常檢查螺栓聯結處有否松動，若有應及時緊固。
8, often check whether the bolt connection is loose, if there should be timely fastening.
9、設備長時間不用時，應將設備擦凈，用塑料布罩好，以防積塵、銹蝕。
9, when the equipment is not used for a long time, the equipment should be cleaned, covered with plastic cloth, in order to prevent dust accumulation, corrosion.
有了鋁切割設備上面的小總結，希望對廣大客戶有所幫助，如果有什么不理解的或者尋求幫助的請點擊我們的官方網站：http://www.hnyfqpj.cn或者來電咨詢，我們會盡全力為您解決
A small sum aluminum cutting equipment above, hope to help customers, if what you do not understand or seek help please click on our official website: http://www.hnyfqpj.cn or contact us, we will do our best for you to solve